FARALAY PLAY lamppost

FARALAY PLAY mixes music and light so you can enjoy hours and hours of your favorite songs. It connects via bluetooth to your mobile or tablet.

The FARALAY PLAY illuminated outdoor lamp has a vegan leather handle that allows you to move it anywhere comfortably and easily, in addition, the feeling is very pleasant to the touch. Equipped with a wireless base you can play through its remote control with the colors that will appear inside

All Newgarden products are made of polyethylene, so they are lightweight and very resistant to extreme temperatures. They are also protected against UV rays, making the life of the product extraordinarily long.

TECHNICAL INFORMATION

- Type: LED BULB
- Fixing system: screwed
- Connection: DC JACK
- Battery: 2000mAh lithium
- Autonomy Direct charge: 6-8h hours
- Solar charging power: ---
- Power: 15W 40lm 12leds
- Charging method: direct charging
- Operating voltage: 5 V
- LED type: RGB DIP
- Color: RGB
- Final color: white
- Material: ABS
- IP: 30
- Half life: 10,000 h
- Light opening angle: 360º
- Light temperature: RGB
- Charge cycles: 500
- IR command: YES
- Charging time: 6h
- Speaker power: 5W x 1 speaker
- Type: LED BULB
- Accessories: screwed
- Connection: DC JACK
- Battery: 2000mAh Lithium
- Direct charge battery life: 6-8h
- Solar panel energy:
- Power: 15W 40lm 12leds
- Charging method: direct charging
- Voltage: 5V
- LED type: RGB DIP
- Color: RGB
- Finish color: white
- Material: ABS
- IP: 30
- Product shelf life: 10,000 h.
- Angle: 360º
- Light temperature: RGB
- Battery life (cycles): 500
- Remote control: YES
- Charging time: 6h
- Speaker power: 5W x 1 speaker
-Measures: 21x39 cm.

Instructions for use Read the instructions for use carefully before handling the product.

Technical specifications 1) Mounting: E27 LED bulb (Max. 25W) 2) Degree of protection: IP65 (Outdoor)

WARNING

1) To avoid falls and / or electric shock, the lamp must be installed according to these operating instructions.

2) To avoid falls, electric shock, breakage, etc., do not personally change any part of this lamp.

USE NOTE

1) Operating voltage 100-240V frequency 50 / 60Hz, do not exceed this voltage.

2) This lamp is not protected against immersion in water, if improperly installed, it will cause electrical accidents.

3) To avoid fires, do not put high temperature objects or materials under the lamp for a long time.

4) To avoid failures, do not connect to another regulator or switch in the adjustable function.

5) In case of abnormal operation, turn off the power and contact qualified personnel.

6) sach4events is not responsible for improper use of the lampholder or the assembly that forms the product.

MOUNTING INSTRUCTIONS (bulb replacement)

Disconnect the product from the mains.

Unscrew the electrical assembly to remove it from the product.

Unscrew the bulb with E27 socket and replace with the replacement bulb.

Screw the electrical assembly back into the product.

Connect to the mains

(*) 1. Instructions are subject to revision.

2. Characteristics may vary due to product improvements.

3. For more information contact us through the contact form on the web.

Instructions for use Read the instructions for use carefully before handling the product.

1) Mounting: Exchangeable T8 LED tube, connection to one end

2) Lumens: 100 Lm / W

3) Degree of protection: IP65 (Outdoor)

USE NOTE

1) Operating voltage 100-240V frequency 50 / 60Hz, do not exceed this voltage.

2) This lamp is not protected against immersion in water, if improperly installed, it will cause electrical accidents.

3) To avoid fires, do not put high temperature objects or materials under the lamp for a long time.

4) To avoid failures, do not connect to another regulator or switch in the adjustable function.

5) In case of abnormal operation, turn off the power and contact qualified personnel.

6) Newgarden Spain is not responsible for improper use of the lampholder or the assembly that forms the product.

MOUNTING INSTRUCTIONS (bulb replacement)

Disconnect from the mains Remove the assembly by unscrewing from the base Unscrew the grip washer to the Led tube and slightly separate the two fixing pillars to be able to remove the tube.

Remove the tube from the base.

Connect the new tube through the connecting part (the tube must be connected to one end and the connected part must be the one indicated on the Led tube) Insert the washer through the tube until it reaches the base, slightly tighten the two pillars throttling Slightly the led tube and screw the fixing washer.

Insert the assembly into the product, screw the base into the ring.

Connect to the electric current.

(*) 1. Instructions are subject to revision.

2. Features may vary due to product improvements. 3. For more information contact us through the contact form on the web.

WiFi repeater installation Device configuration as signal repeater.

1) Connect the device to the electrical power making sure that it is within the coverage area of ​​your main wireless network.

2) Once on, search for the “COMFAST” Wi-Fi network on your mobile device, Tablet or Iphone.

3) After connecting to the device, open your browser and type the following in the address bar: 192.168.10.1 The following should appear (A)

4) Both username and password are in both cases "admin" without quotes. Then press the Login button

5) Upon entering you will see a screen like the one shown in the image below, where it will be established in which mode the device will work: AP, Repeater or Router.

Choose the Repeater option. (B)

6) Subsequently the device will scan the nearby wireless networks and present them, so that you select which wireless network you want to repeat. For our example we will use the Eurocomputer network, which appears first according to the intensity of its signal. (C)

7) Once the wireless network to be repeated is selected, it will ask us for a name for the SSID, that is, the name that the computers that want to connect to it will see.

In our example we will leave it with the default name COMFAST but you can put any name as “terrace” or “garden”.

At this point, the only precaution we should take is to establish the same password (Pre-Shared Key) that we use to connect to our home wireless network regularly. (D)

8) After setting the above parameters, click on the Connect button. The device will restart and it will be ready for operation.

LOADING INSTRUCTIONS

Option 1 / Solar:

1) Leave the product exposed to the sun as long as possible. Product dimensions and hours of exposure may vary the download time of the product.

Option 2 / Battery

1) A full charge is recommended before first use. 2) Connect the charger to the plug. 3) During charging, the charger indicator light is red; It will turn green or blue once the charge is completed.

Instructions for use Read the instructions for use carefully before handling the product.

Technical specifications

1) Adapter: Input 100 - 240AC, output 5V / 1A

2) Power: 10W Acoustic, 5W lamp

3) Usage time: 6 - 8 hours

4) Charging time: 6 hours

5) Bluetooth name: “Speaker Lighting”

WARNING

1) To avoid falls, electric shock, the lamp must be installed according to these operating instructions.

2) To avoid falls, electric shock, breakage, etc., do not personally change any part of this lamp.

USE NOTE

1) Voltage voltage (Adapter) 100-240V frequency 50 / 60Hz, do not exceed this voltage.

2) This lamp is not protected against water, if improperly installed, it will cause electrical accidents.

3) To avoid fires, do not put high temperature objects or materials under the lamp for a long time.

4) To avoid failures, do not connect to another regulator or switch in the adjustable function.

5) In case of abnormal operation, turn off the power and contact qualified personnel.

6) If the speaker is filled with water the sound is distorted, empty the water that could have been introduced through the grill.

7) Use only the components provided by the manufacturer. Any other electronic component other than the one supplied may seriously damage the operation of the product.

TAKE NOTE After 20 minutes of inactivity, without music or connection, the connection must be restarted. LOADING INSTRUCTIONS

1) A full charge is recommended before first use.

2) Connect the charger to the plug.

3) During charging, the charger indicator light is red; It will turn green or blue once the charge is completed.